Drilmax Precision Tubes.

Seamless Precision Tubes for Mineral Exploration Drilling
Available Through Solsteel

Use

Drilmax is Vallourec Precision Etirage's trademark for the range of products dedicated to the manufacturer of diamond core drill rods, core barrels and casings.  Drilmax tubes have been designed specifically for drilling industry and therefore meet the most demanding requirements in terms of straightness, concentricity and yield strength.

Core drilling standards

American (DCDMA)
British (BS 4019)
Swedish (Metric)

Material analysis and mechanical properties

Mechanical Properties
Material Analysis
Yield Strength min.
MPA
Ultimate Tensile Strength min.
MPA
Elongation min. guage length
(51mm or 2")
Brinell Hardness
**
Typical chemical composition % max.
C
Mn
Si
Mo
Cr
V
P
S
Drilmax 550*
550
690
18
200-270
0,20
1,60
0,50
0,025
0,025
Drilmax 620*
620
725
17
230-280
0,44
1,65
0,30
0,035
0,035
Drilmax 650*
650
790
15
0,33
0,60
0,35
0,25
1,10
0,035
0,035
Drilmax 700*
700
800
15
0,22
1,60
0,50
0,15
0,035
0,035
Drilmax 730*
730
820
15
0,44
1,65
0,50
0,035
0,035
Drilmax 800*
800
900
15
0,45
1,00
0,35
0,25
1,10
0,040
0,035
Drillmax 850
850
950
15
0,42
1,70
0,45
0,02
0,20
0,10
0,035
0,035

* Available in premium machinability steel grade with S between 0,015 and 0,040
** Only available for tubes with WT over 5mm

Dimensional range and tolerances

Drilmax tubes are manufactured to internationally accepted dimensions and tolerances, in a range covering OD 0.98" to 7.007", to suit the most widely used wireline and conventional rods, core barrels and casings designs.

Wireline drill rod tubes

mm
mm
Designation
Outside diameter
Inside diameter
Outside diameter
Inside diameter
Max.
Min.
Max.
Min.
Max.
Min.
Max.
Min.
A Wireline
45.45
44.70
35.07
34.82
1.750
1.760
1.381
1.371
B Wireline
55.55
55.80
46.20
45.95
2.187
2.197
1.819
1.809
N Wireline
69.85
70.10
60.32
60.07
2.750
2.760
2.375
2.365
H Wireline
88.90
89.28
78.00
77.62
3.500
3.515
3.071
3.056
P Wireline
114.30
114.68
103.17
102.79
4.500
4.515
4.062
4.047
S Wireline
139.70
140.08
125.50
125.12
5.500
5.515
4.941
4.926

"W" Design flush joint casing tubes

mm
mm
Designation
Outside diameter
Inside diameter
Outside diameter
Inside diameter
Max.
Min.
Max.
Min.
Max.
Min.
Max.
Min.
RW
36.50
36.63
30.48
30.23
1.437
1.442
1.200
1.190
EW
46.02
46.27
38.35
38.10
1.812
1.822
1.510
1.500
AW
57.15
57.40
48.67
48.42
2.250
2.260
1.916
1.906
BW
73.03
73.28
60.58
60.33
2.875
2.885
2.385
2.375
NW
88.90
89.28
76.58
76.20
3.500
3.515
3.015
3.000
HW
114.30
114.68
101.60
101.22
4.500
4.515
4.000
3.985
PW
139.70
140.08
127.25
126.87
5.500
5.515
5.010
4.995

Tolerance on diameter

Outside Diameter
inches / (mm)
Tolerances
inches / (mm)
Inside diameter
inches / (mm)
Tolerances
inches / (mm)
1" < O.D. ≤ 1.575"
+ 0.0051" -0
I.D. ≤ 2.953"
+0 -0.010"
(25.40) (40)
(+0.13 -0)
(75)
(+0 -0.25)
1.575" < O.D. ≤ 3.150"
+0.010" -0
2.953" < I.D. ≤ 5.512"
+0 -0.015"
(40) (80)
(+0.25 -0)
(75) (140)
(+0 -0.38)
3.150" < O.D. ≤ 5.512"
+0.015" -0
I.D. > 5.512"
+0 -0.018"
(80) (140)
(+0.38 -0)
(140)
(+0 -0.45)
5.512" < O.D. ≤ 7.008"
+0.018" -0
(140) (178)
(+0.45 -0)

Lengths

Drilmax tubes are usually supplied in cut lengths of 10ft (3m), with tollerances of -0 +1/8" (-0 +3mm).  Random or longer cut lengths are also available.

Straightness

Drilmax tubes are delivered with a 1/25":240" (1mm:6000mm) tolerance, with special attention to the tube ends.

Testing, inspection and mill certificates

Drilmax tubes undergo non-destructive testing, by a surface concentrated eddy current technique.  Test certificates showing chemical analysis and mechanical properties are supplied with all products (EN 10204-3.1.B).

Packing

Drilmax tubes are oiled internally and externally, and hexagonally bundled for protection during shipment.

Low residual hoop stress

Vallourec Precision Etirage's Drilmax 730 can be delivered with low residual hoop stress - maximum 80 MPa- on BQ, NQ and HQ dimensions. Drilmax 730 with low residual hoop stress is principally designed for difficult drilling conditions.  Additional information on this highly advanced product is available upon request.

Vallourec Precision Etirage

Vallourec Precision Etirage also manufacture special grades to satisfy individual customer requirements.  This special seamless cold drawn tubing used in the manufacture of drill rods, casings and barrels.

Customers Grades
Maximum Chemical Composition
C
Mn
Mo
P
S
Si
Cr
V
1035
380
900
 
40
50
 
 
 
1043
450
900
 
40
50
 
 
 
N80
200
1500
 
35
35
500
 
 
G95
330
1600
 
35
35
500
 
150
Mécaval 136M
220
1500
 
35
20-40
500
 
 
Mécaval 147M
220
1600
 
35
20-40
500
 
150
Drilmax 620
440
1650
 
35
35
300
 
 
Drilmax 620Q2
440
1650
 
35
20-40
300
 
 
1541
440
1650
 
35
35
500
 
 
1541Q2
440
1650
 
35
20-40
500
 
 
40MnCrV6
420
1700
20
35
35
450
200
100
4130
330
600
250
35
35
350
1100
 
4140
430
1000
250
40
40
350
1100
 
4142
450
1000
250
40
20-35
350
1100
 
Customer Grades
Yield Strength
Re(MPa) min.
Tensile Strength
Rm(MPa) min.
A%
min
A2"
Heat Treatment
1035
550
620
15
+SR
1043
550
620
15
+SR
N80
550
690
18
+SR
G95
630
765
15
+SR
Mécaval 136M
550
690
15
+SR
Mécaval 147M
630
765
15
+SR
Drilmax 620Q2
620
725
15
+SR
1541Q2
700
813
15
+SR
40MnCrV6
900
950
15
+SR
4130
650
750
15
+SR
4140
650
790
15
+SR
4142
740
880
15
+N+SR